How to Make a Korker Hair Bow

Korker Hair Bows are one of my favorite Boutique Hair Bows and among the most expensive, with Gymboree selling them for around $5 each to boutiques selling them for as much as $10 each. Making your own Korker Hair Bow is fairly easy, and is much less expensive.

To make your own Korker Hair Bows you will need ¼ inch or 5/16 inch dowel rods, wooden clothespins, 100 % 3/8 inch wide polyester ribbon it can be grosgrain, satin, jacquard, or organza, string or elastic, glue gun, and Fray Check or clear nail
 polish.

Preparing Your Korker Ribbon

The first step in making your Korker Hair Bow is to prepare your Korker Ribbon. For this you will need your dowel rods, which can be purchased at any local Hardware Store. When you purchase dowel rods, they are usually long and you will need them to be somewhere between fifteen and seventeen inches long, so you can either have someone at the store cut it for you or you can cut it yourself.

The first thing you will want to do is to preheat your oven to 275 degrees. Once you have done that you will need to place your ribbon at the top of the dowel rod, and secure it tightly using a clothespin, after the ribbon is secure you will begin twisting the ribbon tightly around the dowel rod. I have heard many people say that putting the end of the dowel rod into a drill tip, and using the drill to twist the ribbon is easier, but I am not extremely coordinated so I usually wrap the ribbon by hand. Once you get to the end of the dowel rod you will want to cut the ribbon and secure the end of the ribbon to the dowel rod with a second clothespin.

After you have finished wrapping the ribbon around your dowel rods you will be ready to place your ribbon into the oven. You can do this one of two ways, you can line your oven rack with aluminum foil and place your dowel rods directly onto the oven rack or you can place the dowel rods on cookie sheets lined with aluminum foil. However you choose to place your dowel rods into the oven, you will want to leave them in the oven for about twenty-five minutes.

 
Comments 1 - 10 of 14 Next >>
Comments
Type in Your Comments Below

Hello, Jean to answer your questions: a) you measure the grosgrain ribbon after it has been baked. Use a ruler and cut 2 inch pieces for approximately 3 inch bows or 3 inch pieces for 4 inch bows. Do not stretch the ribbon out. You want to keep it curled and full. Make sure you use quality ribbon like Schiff's grosgrain. You can find it at www.houseofribbon.com for inexpensive. Schiff grosgrain ribbon bakes extremely well and holds the curls much better. I hope this helps!

Posted on 03/24/2009 at 9:03:38 PM

I'm new at this. How do you measure these to cut? Do you stretch them out or measure them curled? 2 1/2 inches is awfully short if you stretch it.

Posted on 10/29/2008 at 8:10:23 AM

You spray with spray starch before putting them in the oven.

Posted on 10/04/2008 at 10:10:13 AM

when do you spray before putting them in the oven or after taking them out?

Posted on 09/03/2008 at 11:09:14 AM

I have been making these for years all you have to do really is just twist the ribbon tight and tie the two ends together and place into the oven at 350 for 5 mins then let cool and cut ends off and there you go. u never need any rods or anything. it takes to much time up!

Posted on 03/23/2008 at 2:03:29 PM

Hey guys I am new to this. I LOVE putting these bows in my daughter's hair but they are just so darn expensive. So I am going to try and make them. How would I go about attaching these to pony tail holders? Simply hot glue? Or is there a better way? Thanks so much.

Posted on 02/14/2008 at 11:02:05 PM

Wow thanks! Love those korker bows! BTW, I also found some awesome hair bow instructions online at www.sweetbabybowtique.com They show how to make SO MANY different kinds! JFYI :) ~~**Kat**~~

Posted on 01/07/2008 at 10:01:21 AM

Oh, and yes you can use most any type of ribbon. I like to play around with different types of ribbon, and have had some really great results!

Posted on 12/18/2007 at 11:12:42 AM

I have heard several people say that they spray their ribbon with Spray Starch before putting them in the oven. I have never tried this but they swear by it. I hope that helps!

Posted on 12/18/2007 at 11:12:50 AM

is there something you have to put on the ribbon to stiffen it, and can you use any kind of ribbon??

Posted on 12/02/2007 at 12:12:00 PM

Comments 1 - 10 of 14 Next >>