Slate Tile Flooring Dos and Don'ts

A Selected List to Guide in the Success of Your Slate Tile Floor Installation

Slate Tile Flooring Dos and Don’ts

The popular use of slate tile flooring in many areas of residential and commercial interiors and exteriors is a tribute to its versatility and aesthetic value. With its distinctive surface, ease of installation and workability, decorative color variation, and its natural slip-resistance
 that makes it a great choice for practicality and look. With slate, you’re always have firm footing!

Do:

• Consider the area in which you wish to install your slate tile flooring and be sure that the type of slate you choose to buy is appropriate with regard to climate, foot traffic, and any other pertinent factors.
• Consider the substrate over which you will install your slate tile, and make sure that it is suitable for your specific choice. Always ask your sales rep about the suitability of your substrate in relation to the slate tile product you buy
• Expect color variations, and use them to your advantage when approaching the layout of your slate tile.
• Read all warranty information provided, and any other instructions or information pertinent to your slate tile flooring purchase
• Layout your slate tile flooring in a dry run, and test the color patterns, thickness variation, and overall spacing of your particular batch of slate
• Use a type of mortar for slate tile that is conducive to your interior or exterior installation. Seek advice from sales reps as to specific brands and varieties of mortar and always read the instructions on any products you buy
• Choose a appropriate slate tile flooring sealant. Some varieties you might consider are high-gloss (which gives your slate tile a lustrous “wet look”), low sheen (which is reflective, but not as shiny as high-gloss), or no sheen, sometimes known as natural finish. The look that these finishes provide are down to taste, but (once again) it’s a good idea to make sure that your sealant is suitable for slate tile
• Hire an experienced flooring professional if you don’t have experience in laying slate tile yourself. This can help you to avoid costly mistakes

 
Comments 1 - 10 of 16 Next >>
Comments
Type in Your Comments Below

Hi, We just installed 16x16 black Brazilian POLISHED 16x16 slate. We were sold SPARKS oil based for the matte/natural finish. Our installer per can directions applied it.It took over 8 hrs to dry. Also it is more of REFLECTIVE/HIGH GLOSS shine. Can we get it back to a natural finish? Using what? Thxs.

Posted on 02/22/2009 at 12:02:10 PM

I want to reface my fireplace from brick to slate tile. Can I mortor the slate over the existing brick or should I build a new wall around the brick?.

Posted on 12/29/2008 at 6:12:59 AM

How well can slate tile be cut? What type of bit is best for making holes (a 3" round shower valve hole)? Thanks

Posted on 12/22/2008 at 12:12:15 PM

okay website were are the donts

Posted on 11/15/2008 at 1:11:20 PM

Yes you do need to remove all tile that does not have a subfloor underneath. Unless you ar eon concrete, if you dont the wood floor with shift with time and the tile and grout with crack

Posted on 11/15/2008 at 1:11:12 PM

My husband and I are buying a home and we noticed the kitchen floor was done in slate and our question is how do you make the high spots in the slate disappear. When we walk on the floor sometimes we will trip and also the kitchen table rocks? Is there any way to correct this problem?

Posted on 10/23/2008 at 3:10:14 PM

Hi, I put in slate flooring throughout my home, but didn't have time to finish it. I called to have someone come in and finish it for me and was advised that I have to remove all that I put down because I didn't lay a sub flooring under it. DO I have to remove, or can I just let it be?:(

Posted on 10/20/2008 at 9:10:33 AM

Hey I removed a stationary island with rounded corners from the middle of the kitchen of the house I just bought. I have replacement slate tile, but I need to know if there is any way I can simply notch corners into the existing slate or would I have to pull up a few lites or what

Posted on 08/31/2008 at 4:08:11 PM

Hi there, i had tumbled 4x4 slate installed on our kitchen backsplash, but the installer didnt clean off all the grout off the tiles themselves, so the whole wall now has a reddish tinge to it because of the grout on the tile. Is there anything i can do to rectify this other than ripping it out and redoing it? Thanks! Jake

Posted on 06/16/2008 at 10:06:44 PM

hey peter removing the slate depends on what the substrate is.if it is treated wood they will just pop right off if it is regular wood how do you feel about a jackhammer? if it is on concrete pull out a big hammer and releive some stress

Posted on 05/27/2008 at 7:05:15 PM

Comments 1 - 10 of 16 Next >>